manualshive.com logo in svg

Azbil MagneW FLEX+, User Manual

Share
Download
Azbil MagneW FLEX+ User Manual Download Page 63

Azbil Corporation 

Installation

MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector 

2-37

To install a flanged detector on a PVC pipe using SUS grounding ring material 

and a protective plate:

Use this method to install the detector using a protective plate to prevent the PVC 

pipe from being deformed or damaged when the bolts are tightened with the specified 

torque.

• 

Install the protective plate between the outer side of the PVC flange and the 

detector, as shown in the figure below. The protective plate protects the PVC 

pipe. The torque level for tightening the bolts is not related to the gasket material.
See Table 2-6 on page 2-26 for the appropriate torque.
See Table 2-7 on page 2-31 for the inner diameter of the gasket.

Protective plate

Lining

Grounding ring

Gasket

Figure 2-28  Installation on a PVC pipe using SUS grounding ring material and a 

protective plate

Summary of Contents for MagneW FLEX+

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands