manualshive.com logo in svg

Azbil MagneW FLEX+, User Manual

Share
Download
Azbil MagneW FLEX+ User Manual Download Page 42

Installation 

Azbil Corporation

2-16 MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector

2.4.8: Installation on a metal pipe using non-SUS 

grounding ring material

The installation methods described in this section are for installation on a metal pipe 

using non-SUS grounding ring material. For the installation method corresponding to 

any other combination of materials, refer to Table 2-5 on page 2-12.
PTFE gaskets are provided for this type of installation. Although rubber gaskets 

can be used, it is not possible to reduce the fastening torque. See page 2-17 for 

installation using rubber gaskets.

 CAUTION

The use of anything other than the PTFE gaskets provided can result in leakage.
The use of rubber gaskets is not recommended and can cause leakage.

To install a wafer detector on a metal pipe using non-SUS grounding ring 

material and a specified torque:

•  Install the detector as shown in the following illustration. The torque level for 

tightening the bolts is not related to the gasket material.
See Table 2-1 on page 2-7 for the appropriate torque.
See Table 2-2 on page 2-10 for the inner diameter of the gasket.

Lining

Grounding ring

PTFE gasket

Figure 2-12  Installation on a metal pipe using non-SUS grounding ring material 

and a specified torque

Summary of Contents for MagneW FLEX+

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands