manualshive.com logo in svg

Azbil MagneW FLEX+, User Manual

Share
Download
Azbil MagneW FLEX+ User Manual Download Page 24

Introduction 

Azbil Corporation

1-10 MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector

1.3.6: Approval of this device

Overview

If 1/2 NPT wiring connection is selected, this device functions as an FM/CSA, non-

incendive -approved model. In this case, the installation standards described in this 

section must be followed.

Installation of this device

FM/CSA Nonincendive model

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS 

(A, B, C, D), CLASS II/III, DIVISION 2, GROUPS (F, G), OR NON-HAZARDOUS 

LOCATIONS ONLY.

 CAUTION

(1) Power supply and internal voltage of ordinary equipment to the earth shall not 

exceed 250 V AC 50/60 Hz, 250 V DC in case on normal / formal conditions.

(2) Ambient temperature is from -25 to 60°C
(3) Process temperature is from -40 to 160°C (Remote model).

Process temperature is from -40 to 120°C (Integral model)

Summary of Contents for MagneW FLEX+

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands