manualshive.com logo in svg

Azbil MagneW FLEX+, User Manual

Share
Download
Azbil MagneW FLEX+ User Manual Download Page 3

MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector 

i

Safety

About This Manual

This manual contains information and warnings that must be observed to keep the 

model MGG/MGS Electromagnetic Flowmeter Detector operating safely. Correct 

installation, correct operation and regular maintenance are essential to ensure safety 

while using this device.
In addition to this model MGG/MGS detector user manual, please refer to model 

MGG10C/14C converter user’s manual for start-up, calibration, trouble-shooting, 

operation, and maintenance of the complete Electromagnetic Flowmeter.
For the correct and safe use of this device it is essential that both operating and 

service personnel follow generally accepted safety procedures in addition to the safety 

precautions specified in this manual.

The following symbols are used in this manual to alert you to possible hazards:

 WARNING

Denotes a potentially hazardous situation which, if not avoided, could result in 

death or serious injury.

 CAUTION

Failure to observe these precautions may produce dangerous conditions that could 

result in operator injury or in physical damage to the device.

Safety Messages

Carefully read this section before in stalling or operating this device.

 WARNING

To prevent the gas or liquid in the pipe from escaping, do not remove the 

electrode cover or the electrodes when the detector is installed on a pipe.

 WARNING

ELECTRIC SHOCK HAZARD! Turn the power supply off before wiring.

 WARNING

This detector is heavy. Dropping it could cause personal injury or damage to the 

device.

Summary of Contents for MagneW FLEX+

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands