manualshive.com logo in svg

Azbil MagneW FLEX+, User Manual

Share
Download
Azbil MagneW FLEX+ User Manual Download Page 57

Azbil Corporation 

Installation

MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector 

2-31

2.5.2: Necessary parts

You will need the following parts to in stall the detector:

•  Connecting bolts and nuts (available separately)

•  Gaskets: Required when using grounding rings made of SUS material. Not 

required when using grounding rings made of other materials.

•  Protective Plate: Required when connecting the detector to polyvinyl chloride 

(PVC) piping.

Gaskets

Gaskets are supplied with the grounding ring, except when it is made of SUS 

material. If you are using SUS material, you must provide the gaskets. Azbil 

Corporation recommends joint sheet or polytetraflouroethylene (PTFE) gasket 

material. For the inner diameters of the gaskets, see the following table. Rubber 

gaskets are not recommended.

 CAUTION

Using a gasket with too small a diameter can affect the flow velocity distribution, 

resulting in inaccurate measurement.
Using a gasket with too large a diameter can cause leakage. Also, any solid 

substance in the fluid to be measured could accumulate between the gasket and the 

flange, resulting in inaccurate measurement.

Table 2-7  Recommended inner diameters of gaskets

Bore diameter 

mm (inch)

Inner diameter 

mm (inch)

2.5

(0.1)

11±1

(0.43±0.04)

5

(0.2)

11±1

(0.43±0.04)

10

(3/8)

11±1

(0.43±0.04)

15

(1/2)

16±1

(0.63±0.04)

25

(1)

25±1

(0.98±0.04)

40

(1½)

40±1

(1.57±0.04)

50

(2)

51±1

(2.01±0.04)

65

(2½)

64±1

(2.52±0.04)

80

(3)

76±1

(2.99±0.04)

100

(4)

101±1

(3.98±0.04)

125

(5)

124±1

(4.88±0.04)

150

(6)

148±1

(5.33±0.04)

200

(8)

196±1

(7.72±0.04)

250

(10)

246±1

(9.69±0.04)

300

(12)

296±1

(11.65±0.04)

350

(14)

346±1

(13.62±0.04)

400

(16)

396±1

(15.59±0.04)

500

(20)

496±1

(19.53±0.04)

600

(24)

596±1

(23.46±0.04)

700

(28)

701±2

(27.60±0.08)

800

(32)

801±2

(31.54±0.08)

900

(36)

901±2

(35.47±0.08)

1000

(40)

1001±2

(39.41±0.08)

Summary of Contents for MagneW FLEX+

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands