manualshive.com logo in svg

Avaya D260, Using Manual, Page: 61 / 99

Share
Download
Avaya D260 Using Manual Download Page 61

Note:

When hide number enabled, base sends SIP header “Privacy: id” to address

sip:[email protected]

The PBX must support anonymous calls otherwise the call will be rejected, and the handset

cannot make an outgoing call if this feature is enabled.

Call forward

The Call Forward feature enables the user to forward all incoming calls in different cases as

described in the following window.

Forward unconditionally

If this feature is enabled all incoming calls to the handset will be forwarded to the number setup in

“Forward To” as shown in following images.

In this case the handset will not receive any incoming calls, but all calls will automatically be

forwarded to the number setup in “Forward To”.

Forward no answer

This feature controls if incoming calls to the handset should be forwarded if the call is not

answered.

Settings

August 2020

Using Avaya Wireless Handset D260

61

Comments on this document? [email protected]

Summary of Contents for D260




































































































Reviews:

No comments