AUI bp-9000e Owner'S Manual Download Page 75

Page: 75 / 80

AUI BP-9000E Owner's Manual

- 69 -

Note: To load envelope, please place it on the paper guide with the front downwards and the

back upwards.

Note:

• Envelope refers to single layer envelope. Printer doesn’t support double layer envelope

and the envelope should not with solid edge.

• When the envelope pulp at the top or bottom, please don’t print at that area with 5mm.

• The sunken place in the bottom of the envelope belongs to the non-printable area.

Please ensure the distance from the bottom sunken line to the printing area is not less
than 5mm.

• Do not use following envelopes:

• Envelopes which with contents in it.

• Envelopes with holes and which both sides are coherent in the middle.

• Envelopes which seal lip parts are folded.

Sample 2 Envelope print direction and printable area

Summary of Contents for bp-9000e

















































































Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands

AUI bp-9000e, Owner'S Manual

Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands