manualshive.com logo in svg

AUI bp-9000e, Owner'S Manual

Share
Download
AUI bp-9000e Owner'S Manual Download Page 10

AUI BP-9000E Owner's Manual 

- 4 - 

2.5 Installing the Paper Rack 

1. Slide the right and left paper guiders to both sides of paper rack. 

2. Install the pivots on both sides of paper rack vertically into the groove of top rear cover. (As shown in 

Figure 2-4) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note: When installing or removing paper rack, please move the right and left paper guiders 

to the corresponding right and left ends.   

 

3. Put the paper rack vertically when using cut sheet paper; when using fanfold paper, please put it 

horizontally. (As Figure 2-5 shown) 

Note: As the multi-ply paper is hard, so in order to avoid paper jam during printing, please 

put the paper rack slantingly when using such kind of paper. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

2.6 Installing the Soundproof Cover 

1. Reverse soundproof board and place it horizontally on the printer. 

2. Plug one hole of soundproof cover into the tab of the L-angle hinge on one side of the printer. 

3. Press the L-angle hinge on the other side inwards gently, plug the other soundproof cover hole into 

the tab, and then loosen it. (As Figure 2-6 shown) 

 
 
 

Top rear cover 

Pivots

Groove 

Figure 2-4 Installing the Paper rack 

Figure 2-5 Placing the paper rack 

Tractor 

Multiple fanfold paper 

Print head 

Single ply fanfold paper 

Print head

Tractor

Frivtion roller 

Cut sheet paper 

Print head 

Platen

Summary of Contents for bp-9000e

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands