AUI bp-9000e Owner'S Manual Download Page 29

Page: 29 / 80

AUI BP-9000E Owner's Manual

- 23 -

3.1.7 Self-test

Before self-test, please make sure ribbon cartridge has been installed correctly and paper in. There
are kanji self-test and ASCII self-test.

During self-test, ONLINE LED turn on and LCD shows the current self-test state.

ASCII self test

1. LQ self test mode: When the power is off, press

LF + ONLINE

keys while turning on the printer; and

then press

LF + RESET

keys at the same time, and then loosen the

RESET

key, but go

on pressing

LF + ONLINE

keys until self-test starts.

2. Draft self test mode: When the printer power is off, press

key while turing on the printer; then

press

RESET

keys at the same time, then lossen

RESET

key but go on pressing

key until

the self-test starts.

Stop self-test

Press

ONLINE

key to stop self-test temporarily.

Go on self-test

After stopping self-test temporarily, press

ONLINE

key to go on self-test.

End the self-test

During self-test, press

RESET

key or turn off the printer to end the self-test.

3.1.8 Tear Off

Tear off function is only for fanfold paper.

After pressing

TEAR OFF

key, paper would be fed to the paper cutter for tear off.

Note: When you tear off the paper for the first time, if the top of paper does not over the paper

cutter, please press TEAR OFF key one more time to feed the paper back to the original
position.

3.1.9 Shortcut Key Function

Function Key

Resume default setting
(Initialization 1)

PARK + Q LF + M.RLF + POWER ON

ASCII LQ self-test

LF + POWER ON

ASCII Draft self-test

LF + POWER ON

H-Dump in LQ mode

FF + POWER ON

H-Dump in Draft mode

FF + POWER ON

Paper cutter

SELF TEST DRAFT

Summary of Contents for bp-9000e

















































































Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands

AUI bp-9000e, Owner'S Manual

Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands