AUI bp-9000e Owner'S Manual Download Page 13

Page: 13 / 80

AUI BP-9000E Owner's Manual

- 7 -

2.8.3 Connecting to the USB Interface

1. Plug the USB cable A end (flat shape) into the computer's USB interface.

2. Plug the USB cable B end (square shape) into the printer's USB interface. (As Figure 2-11 shown)

Note: Don't impact the plug after connecting the USB cable.

2.8.4 Connecting to the Ethernet Interface

Plug the RJ-45 crystal plug of the Ethernet cable into the printer, and plug the other plug into the LAN.
As shown in Figure 2-12.

Note: The details of the network setting please refer to the relative contents in this

owner’s

manual.

2.9 Connecting to the Power Cord

1. As shown in Figure 2-13. Make sure the printer is turned off. (The pressed down side of the power

switch with “O” marks denotes the printer is off.)

Figure 2-11 Connect to the USB interface

Figure

2-12

Connect to Ethernet interface

Figure 2-10 Connect to the serial interface

Serial cable

Serial interface

Screw

USB cable

USB interface

Ethernet interface

Ethernet cable

Summary of Contents for bp-9000e

















































































Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands

AUI bp-9000e, Owner'S Manual

Search results

Summary of Contents for bp-9000e

Reviews:

Related manuals for bp-9000e

Brands by name

Popular brands