Atmel ATmega128 Manual Download Page 377

Page: 377 / 386

377

2467S–AVR–07/09

ATmega128

Rev. 2467D-03/02

Added more information about

“ATmega103 Compatibility Mode” on page 5

Updated

Table 2, “EEPROM Programming Time,” on page 23

Updated typical Start-up Time in

Table 7 on page 38

Table 9

and

Table 10 on page 40

Table 12 on page 41

Table 14 on page 42

, and

Table 16 on page 43

Updated

Table 22 on page 57

with typical WDT Time-out.

Corrected description of ADSC bit in

“ADC Control and Status Register A – ADCSRA”

on page 244

Improved description on how to do a polarity check of the ADC differential results in

“ADC Conversion Result” on page 241

Corrected JTAG version numbers in “JTAG Version Numbers” on page 256.

Improved description of addressing during SPM (usage of RAMPZ) on

“Addressing

the Flash During Self-Programming” on page 278

“Performing Page Erase by SPM”

on page 280

, and

“Performing a Page Write” on page 280

Added not regarding OCDEN Fuse below

Table 118 on page 288

10. Updated Programming Figures:

Figure 135 on page 290

and

Figure 144 on page 301

are updated to also reflect that AVCC

must be connected during Programming mode.

Figure 139 on page 297

added to illustrate

how to program the fuses.

11. Added a note regarding usage of the PROG_PAGELOAD and PROG_PAGEREAD

instructions on

page 307

12. Added Calibrated RC Oscillator characterization curves in section

“Typical Charac-

teristics” on page 333

13. Updated

“Two-wire Serial Interface”

section.

More details regarding use of the TWI Power-down operation and using the TWI as master
with low TWBRR values are added into the data sheet. Added the note at the end of the

“Bit

Rate Generator Unit” on page 204

. Added the description at the end of

“Address Match Unit”

on page 205

14. Added a note regarding usage of Timer/Counter0 combined with the clock. See

“XTAL Divide Control Register – XDIV” on page 37

Rev. 2467C-02/02

Corrected Description of Alternate Functions of Port G

Corrected description of TOSC1 and TOSC2 in

“Alternate Functions of Port G” on page 85

2. Added JTAG Version Numbers for rev. F and rev. G

Updated Table 100 on page 256.

Added Some Preliminary Test Limits and Characterization Data

Removed some of the TBD's in the following tables and pages:

Summary of Contents for ATmega128



































































































































































































































































































































































































Search results

Summary of Contents for ATmega128

Reviews:

Related manuals for ATmega128

Brands by name

Popular brands

Atmel ATmega128, Manual

Search results

Summary of Contents for ATmega128

Reviews:

Related manuals for ATmega128

Brands by name

Popular brands