AstroJet M1DX Operator'S Manual Download | Manualshive

Page: 34 / 97

background image

SECTION 2
ASSEMBLE/INSTALL PRINTER

28

Install Printhead Cartridge

Printhead Cartridge is a delicate precision device. Handle with extreme care to avoid damage and issues that could
degrade print quality.

CAUTION



Use electrostatic discharge (ESD) protection when handling.



Hold Printhead Cartridge by handles ONLY.



DO NOT touch ink couplings, nozzle surface or electrical contacts.



DO NOT unpack Printhead Cartridge until Printer is ready for
installation. Once unwrapped, delay in installing Printhead can
compromise print quality due to dehydration.



DO NOT place an unwrapped Printhead on any surface before installing.
Protect Printhead from scratches, dust, fibers, dirt and other
contaminants at all times.

1.

With Printer power ON, lower Duplex Feeder. Open Print
Engine Access Door on Duplex Printer. Unlatch and pull out
Print Engine.
Press

Printhead Latch Release Button

[1]

. Printer runs,

then Latch pops open

[2]

.

NOTE: Remove Cap Protectors on Ink Nozzles [3].
Be sure to open Latch fully to retract Ink Nozzles.

CAUTION

DO NOT PRY OR MANUALLY LIFT PRINTHEAD
LATCH OR LATCH MAY BREAK. ONLY OPEN
LATCH USING RELEASE BUTTON ON
PRINTER OR PRINTHEAD RELEASE
COMMAND IN PRINTER TOOLBOX.

«
...
32
33
34
35
36
...
»

Summary of Contents for M1DX


































































































Reviews:

No comments

Related manuals for M1DX

Brand: Labelmate Pages: 2

Brand: Canon Pages: 4

PIXMA TR4500 Series

Brand: Canon Pages: 100

Brand: Xerox Pages: 418

Brand: Zonestar Pages: 25

Aficio SP C730DN

Brand: Ricoh Pages: 100

WorkCentre Pro 421

Brand: Xerox Pages: 162

MINI THERMAL RP-3180

Brand: TVS electronics Pages: 19

Brand: IBM Pages: 16

Brand: Unisys Pages: 144

Brand: Custom Audio Electronics Pages: 88

Brand: CognitiveTPG Pages: 2

Brand: Xante Pages: 106

Brand: Oki Pages: 72

Brand: Wang Pages: 39

Brand: Samsung Pages: 17

Brand: Oki Pages: 76

Brand: Oki Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands