manualshive.com logo in svg

AstroJet M1DX, Operator'S Manual

Share
Download
AstroJet M1DX Operator'S Manual Download Page 24

SECTION 2 
ASSEMBLE/INSTALL PRINTER 

 

18 

 

8.

 

Finished software installation.

 Do not check the 

Print 

Test Page

 as Printer is not set up yet.  

You can check “Set this printer as the default printer” at 
this time. Click 

“Finish”

. 

 

 

 

 

 

 
 

9.

 

Install Printer Software.

  

Click 

“Exit”

 to close CD.

 

10.

 

Restart computer to complete installation.

 

 

 

 

 
 
 

Install Over Network Connection, Version A  

Use this procedure to install the Print Driver over the Network connection. This procedure works for almost all 
networks that allow 

automatic assignment of the IP address

 (

factory default

).  

NOTE: Copy the 12-digit Hardware ID number listed on the Printer(s) on the label located just below the 
Ethernet port so you can identify the Printer(s) in a later step.

 

1.

 

Check that the 

Top Printer

 is plugged in and turned ON.  

Make sure the Ethernet (

network

) cable is plugged into the 

Ethernet port on the Printer.

 

NOTE: Duplex Printer should 

not be connected to the Top Printer at this time.  

Install disk supplied with Duplex Printer in your CD drive. When 

AutoPlay 

Window opens, click 

“Run Setup.exe”

 to start. 

 

 

 

 
 

2.

 

Install Printer Software.

 Make sure computer system 

meets 

minimum requirements

 and you followed other 

instructions listed on screen.  
Click 

“Install Printer Software”

.

 

 

 

 

 

 

Summary of Contents for M1DX


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands