manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 9

TeleBoss 850 2.06.280_STD User Manual 

 

Page 3 

 

3. 

 

Using wire nuts (not supplied), connect the stripped wires to the power source.  The red wires connect to ground 
or the most Positive connection on the voltage source.  The blue wires connect to -48VDC or the most Negative 
connection on the voltage source. 

 
 

Option B:

  Use the supplied kit to make a wire harness: 

1. 

 

You will need a crimping tool that crimps standard Molex type 18-24 AWG Mini-Fit Terminals (Molex Part 
Number: 39-00-0060, Engineering Series 5556). 

2. 

 

Crimp the supplied terminals to your cable connections. 

3. 

 

Insert the crimped terminals into the supplied white nylon housing.  Orient the housing so the latching mechanism 
is up and you are looking into the  large end of the housing.  See diagram above.  Insert the 2 Ground or Most 
Positive leads into the upper and lower compartments on the left side of the connector, e.g. the same positions as 
the red wires on the supplied harness assembly.  Insert the 2 -48VDC or Most Negative leads into the upper and 
lower compartments on the right side of the connector, e.g. the same positions as the blue leads on the supplied 
harness assembly. 

4. 

 

Connect the completed assembly into the power input receptacle at the rear of the unit. 

 
 

Accessing the Command Line via a Serial Connection 

 
1.  Connect to I/O 2 with a serial terminal emulation program at 19200 baud, 8N1. 
2.  Enter 

STATUS

 or 

?

 and press <Enter>.  You will be presented with a status screen similar to the following. 

 

 
TeleBoss 850 2.06.280 STD  -  Status 
Site Name       : 850-850000163 
Serial Number   : 850000163        Eth 1    : STATIC 
Date            : THU 03/03/2011   IP Addr  : 0.0.0.0 
Time            : 08:02:48         MAC Addr : 00:10:A3:60:02:3E 
Memory          : 32768K           Eth 2    : STATIC 
% Full Alarm    : OFF              IP Addr  : 0.0.0.0 
No-Data Alarm 1 : OFF              MAC Addr : 00:10:A3:60:02:3F 
No-Data Alarm 2 : OFF              Modem    : Yes 
Duplex          : FULL 
------------------------------------------------------------------------- 
Port   Baud/Etc.  Recs     Bytes    Full Wrap Name 
IO1  : 19200,8N1  00000000 00000000   0% OFF  I/O 1 
IO2  : 19200,8N1  00000000 00000000   0% OFF  I/O 2 
 
COMPLETE 
> 

 
When the status screen appears, the unit is successfully connected and ready for use. 
 

Accessing the Command Line via the Asentria OmniDiscover program 

 
1.  From the Asentria website (

http://www.asentria.com/docsandsoftware/productManuals.aspx

), or the 

Documentation and Utilities CD, download the OmniDiscover program.  This program will allow you to locate 
devices on your network (ie: the T850) with Asentria MAC addresses, and allow you to assign the network 
settings directly over the network, thus eliminating the need for the serial port connection as described above. 

 
2.  Open the OmniDiscover program.  It will immediately display all Asentria devices on the network.  Right clicking 

on the line for this unit displays three options:  Setup, Telnet and Web. 

 

Setup

 opens another window where the IP Address, Subnet Mask, and Gateway (router) can be configured 

(see below).  Press “OK” and these will be assigned to the unit and displayed in the previous window.  (Select 
this option to configure the network settings for the first time.) 
 

Telnet

 opens a connection to the device using your default Telnet client. 

 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands