manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 31

TeleBoss 850 2.06.280_STD User Manual 

 

Page 25 

 

 
Idle Connection Disconnect (sec) 

sets the number of seconds to wait before disconnecting an idle connection.  A 

setting of 0 means the unit does not disconnect due to an idle connection.  Default setting is 60 seconds.

 

 
Maximum Retries 

defines the maximum number of times to retry a failed connection.  Default setting is 3.

 

 
Carrier Detect / Login Sequence Timeout (sec) 

configure standard login timeouts, from 0 to 65535 seconds.  

Default setting is 60 seconds for Carrier Detect, and 30 seconds for Login Sequence.

 

 
Dialout Modem Init String 

sets the modem initialization string.  (Max length 48 chars)

 

 
IP Address to Suggest 

sets an IP to try to acquire, if defined.  Default setting is 0.0.0.0 

 

Setting Key: 

net.pppdial.downafter.ftppush 

Values are ON or OFF (default OFF).  ON means that if FTP Push raised PPP, then it kills PPP when finished. 

 
PPP Hosting Settings 
 

 
TeleBoss 850 - PPP Hosting Settings 
A) PPP Hosting Enabled                  [OFF] 
B) Idle Connection Disconnect (sec)     [60] 
C) Local (Device) IP Address            [192.168.105.1] 
D) Remote (Caller) IP Address           [192.168.105.2] 
 

 

PPP Hosting Enabled 

is an ON/OFF toggle to enable inbound PPP connection hosting.  Default setting is OFF.

 

 
Idle Connection Disconnect (sec) 

sets the number of seconds (0 

– 65535) to wait before disconnecting an idle 

connection.  A setting of 0 means the unit does not disconnect due to an idle connection.  Default setting is 60 
seconds.

 

 
Local (Device) IP Address 

sets the IP address of the T850 for the PPP session.  Default is 192.168.105.1

 

 
Remote (Caller) IP Address 

sets the IP address of the calling device for the PPP session.  Default is 192.168.105.2. 

 
IP Routing 
 

 
TeleBoss 850 - IP Routing 
A) Route PPP to Ethernet                [OFF] 
B) Route Ethernet to PPP                [OFF] 
C) Ethernet to PPP NAT Enable           [ON] 
D) Ethernet Interface                   [ETH1] 
 

 
Each of the above options toggles settings for routing TCP/IP packets of specific types and origins to and from a 
device connected via PPP. 
 

Route PPP to Ethernet

 toggles ON/OFF to enable the T850 to forward IP frames originating on PPP that are not IP-

addressed to the unit, as well as forward IP frames received on Ethernet that are associated with forwarded frames 
that originated on PPP.  Default setting is OFF. 
 

Route Ethernet to PPP

 toggles ON/OFF to enable the T850 to forward IP frames originating on Ethernet that are not 

IP-addressed to the unit, as well as forwards IP frames received on PPP that are associated with forwarded frames 
that originated on Ethernet.  Default setting is OFF. 
 

Ethernet to PPP NAT Enable

 toggles ON/OFF to enable the T850 to do network address translation on these 

forwarded frames.  Default setting is ON. 

 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands