manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 18

TeleBoss 850 2.06.280_STD User Manual 

 

Page 12 

 

Serial Ports

 

Each of the two (or more) serial ports is configured as a DTE port using an RJ45 connector.  This is the standard 
recommended pinout for EIA/TIA-561 for 8 pin RJ45 connector: 
 
PIN1 

=RI  

=RING INDICATOR, INPUT to the T850 

PIN2 

=DCD  =CARRIER DETECT, INPUT to the T850 

PIN3 

=DTR  =DATA TERMINAL READY, OUTPUT from the T850 

PIN4 

=SIGNAL GROUND 

PIN5 

=RXD  =RECEIVED DATA, INPUT to the T850 

PIN6 

=TXD  =TRANSMITTED DATA, OUTPUT from the T850 

PIN7 

=CTS  =CLEAR TO SEND, INPUT to the T850 

PIN8 

=RTS  =REQUEST TO SEND, OUTPUT from the T850 

 
The DB9 female cable end which mates with the serial port connectors of connected devices will often have a pair of 
screw-down cable screws.  These cable screws should be used to assure a solid connection of the cable with the 
device. 
 
Default settings for the serial ports are 19200-baud, 8-bit word length, no parity, and one stop bit (19200, 8N1).  Use 
the internal setup menu to adjust these settings.

 

 

Internal Modem 
If a dialup POTS modem is installed, an RJ11 (typical U.S. phone) connector is used.  A POTS (analog) dialup phone 
line is inserted into this connector.  The modem installed within this unit is FCC certified.  For further information, 
consult the 

Internal Modem Guidelines 

appendix or the serial number label on the bottom of the T850. 

 

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

 

 

 

ATTENTION: Pour réduire les risques d’incendie, utilizer uniquement des conducteurs de télécommunications 26 AWG au 
de section supérleure. 

 
*  Expansion Card Slots 
Optional Expansion Cards can be installed to expand the capabilities of the T830-2 and T830-6.  Contact Asentria 
Sales (

[email protected]

) for more information on Expansion Cards. 

 
DIP Switches 

The bank of 8 DIP switches on the back panel of the T850 are used to control the baud and parity settings of I/O2, to 
set 

the operational mode for I/O2, and to put the unit into “boot load mode” where it can be forced to load a new 

application (firmware image).  The following table shows how to set the various DIP switches to obtain certain 
settings: 
 

I/O 2 Baud   

SW1    

SW2     

2400         

DOWN    DOWN    

9600         

UP   

DOWN      

19200        

DOWN      UP      

115200       

UP 

    

UP       

  

  

  

I/O 2 Word, Parity    

SW3   

  

8N1         

DOWN      

7E1            

UP   

  

  

  

  

I/O 2 Mode 

SW4 

  

Command Mode    

DOWN  

  

Data Mode       

UP  

  

  

  

  

Boot Load Mode 

SW8 

SW1 thru SW7 

No Forced App Reload (Default) 

DOWN  

X (don’t care) 

Forced Application Reload 

UP  

UP  

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands