manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 125

TeleBoss 850 2.06.280_STD User Manual 

 

Page 119 

 

Text1 : 
 
 
 
Hardware: (the value of 

sys.hardware

) 

Product: (the value of 

sys.product

) 

Version: (the value of 

sys.version

) 

Build: (the value of 

sys.build

) 

Serial #: (the value of 

sys.serial

) 

 
 

 Note:

 

There are 3 blank lines before "Hardware:" and 2 blank lines after "Serial #:".  

 
Other more specific types of Asentria Alarm Notice formats are:  (contact 

Asentria Technical Support

 for sample 

format) 

 

Data Alarm notice 

 

No-data Alarm notice 

 

CPE Down Alarm notice 

 

VPN Down Alarm notice 

 

VPNG Down Alarm notice 
 

Version 1.0 for modem dialout 

An Asentria Alarm can also be sent over dialup modem when the Asentria Alarm Version is set to 1.0.  Details of 
this alarm follow: 
 
When an Asentria Alarm is initiated, the box dials into the callout number specified by the action.  Once 
connected, it sends a header and waits for a specific response.  If the T850 receives a specific response to the 
header, it delivers alarms in CRC mode; otherwise, alarms are delivered in non-CRC mode.  In CRC mode, each 
Asentria Alarm is transmitted with some extra control characters and a CRC, and the remote host is required to 
acknowledge each alarm in a certain format.   
 
After all Asentria Alarms have been delivered, the box waits for 20 seconds for any type of keystroke.  If a 
keystroke is detected, the box will present a login menu. 
 
Initial header 
 

 Note:

 

Please see the Control Characters appendix for more information about special characters used within 

this section. 
 
Upon dialing into the receiver, the T850 will send a message similar to the following: 

 

TeleBoss 850   
Server Room B  
Asentria Alarm Notice ver. 1.00  
(CR/LF)(ENQ) 
 

The first line of the output is the T850's answer string. 
The second line is the T850's unit ID. 
The third line indicates the version of Asentria Alarm. 
The final line is the (ENQ) control code. 
 
Non-CRC Mode 
After sending the initial header, the T850 pauses for 10 seconds to wait for an ACK from the receiver.  Non-CRC 
mode requires the Require Asentria Alarm ACKs setting to be turned off.  If the T850 sees no response or the 
receiver replies with: 

 
(ACK)00(ACK)  

 
then non-CRC mode is assumed and the sender will transmit the alarms.  The control characters (SOH), (SOT), 
and (ETX) are not transmitted in non-CRC mode. 
 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands