manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 220

TeleBoss 850 2.06.280_STD User Manual 

 

Page 214 

 

Internal Modem Guidelines 

 
The internal modem supplied with this product complies with Part 68 of the FCC Rules and Regulations.  The labeling 
on the modem provides the FCC Registration number and the Ringer Equivalence Number (REN) for the modem.  
This information is also listed below.  You must provide, upon request, this information to your telephone company. 
 
The REN is useful to determine the quantity of devices you may connect to a telephone line and still have all of these 
devices ring when the number is called.  In most, but not all areas, the sum of the RENs of all devices connected to 
one line should not exceed five (5.0).  To be certain of the number of devices you may connect to a line, as 
determined by the REN, you should contact the local telephone company to determine the maximum REN for your 
calling area. 
 
If the modem causes harm to the telephone network, the telephone company may temporarily discontinue your 
service.  If possible, they will notify you in advance.  If advance notification is not possible, you will be notified as soon 
as possible. 
 
Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect 
proper functioning of your equipment.  If they do, you will be notified in advance to give you an opportunity to maintain 
uninterrupted telephone service. 
 
If you experience trouble with the modem, contact 

Asentria Technical Support

 for information on obtaining service or 

repairs.  The telephone company may ask you to disconnect the device from the network until the problem has been 
corrected or until you are sure that the device is not malfunctioning. 
 
This device may not be used on coin service lines provided by the telephone company (this does not apply to private 
coin telephone applications which use standard lines).  Connection to party lines is subject to state tariffs. 
 

Modem

 

FCC ID

 

REN

 

2400 Baud Modem 

EUD-5U9-BRI4480 

0.8B 

33.6K Baud Radicomm Modem  406CHN-31735-PT-E REN 1.1B  1.1B 
33.6K Baud OmniModem 

6KMUSA-34184-MME REN 0.9B  0.9B 

33.6K Baud MultiModem 

AU7-USA-46014-MD-E  

0.1B 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands