manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 32

TeleBoss 850 2.06.280_STD User Manual 

 

Page 26 

 

Ethernet Interface

 toggles between ETH1, ETH2, or any of the six VLANs that can be configured on either ETH1 or 

ETH2, to inidcate which interface to use for the PPP connection.  Default setting is ETH1. 
 
Refer to the 

IP Routing

 section in the Features chapter for a detailed explanation of IP Routing. 

 
Route Test Settings 
 

 
TeleBoss 850 - Route Test Settings 
A) Route Test Enable                    [OFF] 
B) Minutes Between Tests                [10] 
C) IP Address 1                         [] 
D) IP Address 2                         [] 
E) IP Address 3                         [] 
 

 

Route Test Enable 

is an ON/OFF toggle to enable route testing.  Default setting is OFF.

 

 
Minutes Between Tests 

sets the number of minutes (0 

– 65535) to wait between each round of testing.  Default 

setting is 10 minutes. 
 

IP Address 

n

 sets the hostnames or IP addresses to ping for the test.

 

 

Email Settings 

 

 
TeleBoss 850 - Email Settings 
A) SMTP Server Hostname/IP Address      [] 
B) Email Domain Name                    [asentria.com] 
C) Authentication (LOGIN)               [OFF] 
 

 

SMTP Server IP Address

 sets the hostname or IP address of the outbound mail server.  (Max length 64 chars)  

 

Email Domain Name

 sets the @

domain_name.com 

to use when the T850 sends an Email.  Default setting is 

“asentria.com”.  (Max length 48 chars) 

 
Authentication (LOGIN)

 displays a menu to configure the credentials that may be required by your server for SMTP 

authentication. Some SMTP servers require an authentication to relay Emails.  Default setting is OFF. 
 

 
TeleBoss 850 - Email Authentication Settings 
A) Authentication Enabled               [OFF] 
B) Username                             [] 
C) Password                             [********] 
 

 

Authentication Enabled

 is an ON/OFF toggle to enable Email authentication.  Default setting is OFF. 

 
Username / Password

 defines the login credentials.  (Max length for each is 48 chars) 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands