manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 22

TeleBoss 850 2.06.280_STD User Manual 

 

Page 16 

 

 

Setup Menu 

 

Overview 

 
This section displays screen shots and descriptions taken from the command prompt menu system.  However, the 
menu structure and options are the same as the web interface. 
 
The Setup menu contains all of the configuration options available on the T850.  It is organized in a logical tree 
structure with all settings classified under the following groups:

 

 

 
TeleBoss 850 - Main Setup Menu 
A) Network Settings 
B) Serial Settings 
C) Modem Settings 
D) Security Settings 
E) Alarm/Event Definitions 
F) Action Definitions 
G) General Settings 
H) Event Log Settings 
I) Audit Log Settings 
J) Scripting Settings 
 
Enter your Selection: 
 

 

 Note:

 

Some menus may not be available, depending on your hardware configuration. 

 Note:

 

Passwords are case sensitive and are masked in all menus for security reasons.   

 
Each section in this chapter will go over one of the above setup branches, outlining the options within. 

 

Press either <ESC> or <Enter> to go back one level in the menu tree, or <CTRL + C> to exit any setup menu and 
return to the command prompt.    
 
Since this product allows for multiple simultaneous command processors, two administrators could conceivably 
change the same option at the same time, but due to the multitasking nature of the T850, the changes are processed 
in the order received. 

 

The T850 processes setup changes in real time.  In other words, the unit begins to implement changes to its 
configuration as soon as they are entered.  There is no need to exit a setup menu or reboot the unit to apply changes.  
The exception to this rule is IP-specific network settings.  Changes to these settings are implemented only after all 
open Telnet command processors are closed. 

 

Option Types 

 
String entry 
There are several different types of inputs employed within the Setup menu.  The most common is the string type 
entry: 

A) Site Name                   [Test Site] 

 
When selected, this setting will provide a prompt requesting a new value.  You may press <Enter> or <ESC> to abort 
the option entry or press <SPACE> and <Enter> to delete the current value and leave it blank.  Some numerical or 
required settings will not allow you to leave an option blank, so pay attention to the unit's response when attempting to 
delete a setting's value. 
 
Toggle 
The second most common option type is the toggle type option: 

A) Enable Web Interface      [OFF]  

 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands