manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 19

TeleBoss 850 2.06.280_STD User Manual 

 

Page 13 

 

 

  Note:

 

Boot Load Mode can only be set by flipping ALL DIP switches to the UP position.  This is not a setting that 

can be configured via internal menu settings, or Setting Keys. 
 

 Note:

 

For settings that can be set either via DIP switch, internal menu settings, or Setting Keys, the T850 always 

pays attention to the last setting, regardless of how it was done.  So if the internal setting for I/O 2 Port Mode is 
Command, and someone flips SW4 to the UP position, the Mode is immediately set to Data. 
 

Buttons

 

The only button on the T850 is the Reset button located on the back panel next to the left of serial port I/O 2.  The 
Reset button can be used for two different functions: 
 

1)  To reset the T850 

– press the Reset button for approximately 1 second and T850 will be begin the reboot 

process as described in the 

Power Up Sequence

 section on the next page. 

 
2)   To activate the 

Button Unlock

 feature which resets the username and password back to default. 

 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands