Argus PiCUS Tree Motion Sensor Online Hardware Manual Download Page 75 | Manualshive

Page: 75 / 83

background image

PiCUS TMSO Manual

75

10.3 Switching Off the Devices

After deactivating the system (or even if the devices were only switched on without activating
the system), the devices are in standby mode. To turn them off completely, click the

TURN

OFF

button on the

MGT

tab of the Management Window.

The control unit will then send the command to all TMSO.IMs so that all devices in the system
are switched off together.

NOTE!
For example, if you forgot to wake up one of the sensors so that it could not receive the
deactivation / switch-off command, there is a second possibility:
If you touch the device with the magnetic pen for more than approx. 6 seconds (all LED's go
off), a hardware reset is performed and the device is restarted (LED's light up again after you
remove the magnetic pen).
If you hold the magnetic pen on the device for a longer time, more than 10 seconds, the device
will be switched off completely (LED's remain off even after you remove the magnetic pen).

10.4 Dismantling the Equipment

After the devices have been switched off, you can simply unscrew them from the trees and
take them with you.
Clean the equipment roughly, especially from coarse resin incrustations.
Then place them back in the TMSO.Case for transport and storage.

«
...
73
74
75
76
77
...
»

Summary of Contents for PiCUS Tree Motion Sensor Online




















































































Reviews:

No comments

Related manuals for PiCUS Tree Motion Sensor Online

Brand: ABB Pages: 8

Brand: C-LOGIC Pages: 4

Brand: C-lock Pages: 32

Brand: C-LOGIC Pages: 12

Brand: OHAUS Pages: 32

Brand: Olympus Pages: 4

Brand: Midcontinent Pages: 6

FLEXFLO M4 Series

Brand: Blue-White Pages: 64

Brand: E-Mon Pages: 72

Brand: Victron energy Pages: 46

Brand: Velleman Pages: 38

Brand: Rebel Pages: 28

Brand: Hanna Instruments Pages: 25

Brand: dacell Pages: 39

Brand: Factair Pages: 38

Brand: A&D Pages: 23

Brand: B meters Pages: 30

Brand: Techcomp Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands