Argus PiCUS Tree Motion Sensor Online Hardware Manual Download Page 51 | Manualshive

Page: 51 / 83

background image

PiCUS TMSO Manual

51

7.5 Switching on the Devices

All  devices  are  switched  on  with  the
TMS.Magnetic pen (blunt end with the magnet).
For  the  TMSO.IM,  touch  the  device  with  the
magnetic pen at the recess in the housing:
Hold  the  magnetic  pen  there  until  the  status
LED  lights  up  (approx.  1  second)  and  then
remove it again.
The device is ready for operation as soon as the
status LED starts flashing. It is now in standby
mode  with  activated  radio,  ready  for  a
connection to the TMSO.CU.

CAUTION!
The TMSO.IM will automatically switch off after 15 minutes if no messages are received from
the TMSO.CU!

For the TMSO.CU, first open the housing cover by inserting the screwdriver blade at the rear
end of the magnetic pin into one of the two small openings and lever the snap lock open with
a movement towards the center of the cover.

Now use the magnetic pen to touch the mark with
the

SWITCH

label on the front panel of the device:

Hold the magnetic pen there until the charging and

MEAS LED

light up (approx. 1 second) and then

remove it again.
The unit is ready for operation as soon as the

MEAS-LED

turns off again and the

CON-LED

starts

flashing. It is now in standby mode and with BLE
enabled, ready to connect to your mobile phone.

CAUTION!
The TMSO.CU automatically switches itself off after
5 minutes if it does not receive any messages from
the user's mobile phone!

Figure 22

– Turning on a TMSO.IM

Figure 23 - TMSO.CU

– Opening the cover

Figure 24

– Turning on the TMSO.CU

«
...
49
50
51
52
53
...
»

Summary of Contents for PiCUS Tree Motion Sensor Online




















































































Reviews:

No comments

Related manuals for PiCUS Tree Motion Sensor Online

Brand: Xylem Pages: 24

POCKET COLORIMETER II

Brand: Hach Pages: 188

Brand: M-system Pages: 18

Brand: National Instruments Pages: 15

Brand: Omega Pages: 31

Duomat Evolution DeLuxe

Brand: Dennerle Pages: 27

Brand: Seaward Pages: 2

Ratio:Guard Advanced

Brand: H.E. Anderson Pages: 9

iNELS Air AirCFS-100S

Brand: Elko Pages: 4

Brand: PCE Health and Fitness Pages: 7

Brand: pts Diagnostics Pages: 2

LeakTracker OIL-GLO ULTRA

Brand: Spectroline Pages: 12

Brand: Amrutha Technologies Pages: 22

Brand: Straightpoint Pages: 24

Brand: Kawai Pages: 28

Brand: THORLABS Pages: 63

Brand: Hanna Pages: 44

Brand: Hauber Elektronik Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands