Argus PiCUS Tree Motion Sensor Online Hardware Manual Download Page 59 | Manualshive

Page: 59 / 83

background image

PiCUS TMSO Manual

59

8 System Control and Behavior

This chapter describes in detail the typical behavior of the activated system in the different
measuring modes. The possibilities for controlling the system are also explained.

8.1 Control Panel

8.1.1 General

8.1.1.1 Waking up the Devices

If the system is active, the BLE of the TMSO.CU is deactivated. If you want to reconnect with
your mobile phone the central unit must be woken up.
To do this, open the cover of the device and touch the mark on the front panel with the
designation

SWITCH

with the magnetic pen.

Hold the magnetic pen there until the

CON-LED

lights up (approx. 1 second) and then remove

it again.
As soon as the LED starts flashing, the BLE is active and ready to connect to your mobile
phone. The operating status of the device is not affected by this.

NOTE!
The Internet connection always has priority. See also 8.2.1.1Priorities for Connections.

8.1.2 Wind Reaction Measurement (WRM / WRMS)

8.1.2.1 Setting a Measuring Plan

While the system is active, it will spend most of its time in energy-saving sleep mode. Only
when the period of a set measuring plan is reached it does switch to measuring mode and
records measuring data.
There are 2 possibilities to set a measuring plan:

I.

You set the measurement plan on site via the TMSO.App and the BLE connection to
the TMSO.CU.

To do this, you have to wake up the TMSO.CU (

8.1.1.1Waking up the Devices

) and

then proceed as described in

7.6.1Establish connection to the TMSO.CU

and

7.6.4(optional) Setting a Measuring Plan

II.

Set the measurement plan online via the TMS.Software.
See chapter

4.6.2.6 in the TMS.Software manual

.

8.1.3 Construction Site Monitoring (CSM)

Available via future firmware update.

«
...
57
58
59
60
61
...
»

Summary of Contents for PiCUS Tree Motion Sensor Online




















































































Reviews:

No comments

Related manuals for PiCUS Tree Motion Sensor Online

Brand: F.W. Bell Pages: 75

Brand: VEE GEE Pages: 2

Brand: palintest Pages: 14

Brand: UEi Pages: 8

Brand: +GF+ Pages: 8

Brand: YOKOGAWA Pages: 14

Brand: Kobold Pages: 44

Brand: Rae Pages: 38

Brand: FlowLine Pages: 2

Brand: OHAUS Pages: 6

Panametrics Aurora H2O

Brand: Baker Hughes Pages: 92

Brand: phase II Pages: 11

Brand: X-Rite Pages: 130

Brand: Sagola Pages: 16

Brand: KEM Pages: 49

Liebert MBX Busway

Brand: Vertiv Pages: 16

HP Fire Service

Brand: Neptune Technology Pages: 14

Brand: Fluke Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands