Argox ArgoxScan 9500 Manual Download Page 18

Page: 18 / 154

Interface Selection

This decoder built-in scanner comes in one model and

supports interfaces such as RS232 serial, USB virtual COM

and USB HID. In most of the cases, simply selecting an

appropriate cable and configure the proper interface by following

interface selection.

Interface selection:

You can change factory interface default

(USB Virtual COM ) for other type interface. By plugging

different cables, setting right interface, then scan the interface

barcode, power cycle the scanner will be changed to another

interface. However, you must make sure which cable you need.

RS-232 Interface

USB HID (PC)

USB HID (MAC)

*USB Virtual COM

Summary of Contents for ArgoxScan 9500



























































































































































Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands

Argox ArgoxScan 9500, Manual

Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands