Argox ArgoxScan 9500 Manual Download Page 103

Page: 103 / 154

101

Function Code Transmit

When this selection is enabled and function codes are contained

within the scanned data, the imager transmits the function code to

the terminal.

Function Code Transmit

*Enable

Disable

Intercharacter, Interfunction, and Intermessage

Delays

Some terminals drop information (characters) if data comes

through too quickly. Intercharacter, interfunction, and

intermessage delays slow the transmission of data, increasing data

integrity. Each delay is composed of a 5 millisecond step. You can

program up to 99 steps (of 5 ms each) for a range of 0-495 ms.

Intercharacter Delay

An intercharacter delay of up to 495 milliseconds may be placed

between the transmission of each character of scanned data. Scan

the

Intercharacter Delay

bar code below, then scan the number of

milliseconds and the

SAVE

bar code

Summary of Contents for ArgoxScan 9500



























































































































































Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands

Argox ArgoxScan 9500, Manual

Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands