manualshive.com logo in svg

Argox ArgoxScan 9500, Manual

Share
Download
Argox ArgoxScan 9500 Manual Download Page 22

20

 

RS-232 

 

RTS/CTS-

If the scanner wants to send the barcode data to   

host computer, it will issue the RTS signal first, wait for the   

CTS signal from the host computer, and then perform the   

normal data communication. If there is no replied CTS signal   

from the host computer after the timeout (Response Delay)   

duration, the scanner halts transmission until it detects another 

active CTS signal.   

 

Xon/Xoff-

 When the host computer is unable to accept data, it 

sends a Xoff code to inform the scanner to suspend data   

transmission, and Xon to continue. 

 

ACK/NAK- 

When the ACK/NAK protocol is used, the scanner 

waits for an ACK (acknowledge) or (not acknowledge) from the 

host computer after data transmission, and will resend in response 

to a NAK. 

 

Response Delay 

The unit stays awake to receive data until the RS-232   

Receiver Time-Out expires. A trigger command resets the   

time-out. When an RS-232 receiver is sleeping, a character   

may be sent to wake up the receiver and reset the time-out. 

A transaction on the CTS line will also wake up the receiver.   

The receiver takes 300 milliseconds to completely come up.   

Change the RS-232 receiver time-out by scanning the bar code 

below, then scanning digits from the inside back cover 

of this manual, then scanning 

Save

. The range is 0 to 300   

seconds. Default = 0 seconds (no time-out - always on). 

 

 

 

 

Summary of Contents for ArgoxScan 9500



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands