Argox ArgoxScan 9500 Manual Download Page 10

Page: 10 / 154

Introduction

Installation
RS-232

Disconnect power to the terminal/computer.

Connect the external power supply (DC adapter) to the serial

interface cable of the scanner.

Plug the serial connector into the serial port on the back

of your computer/terminal. Tighten the two screws to secure

the connector to the port.

Plug the power pack into power source.

Once the scanner has been fully connected, turn the

terminal / computer power back on.

USB (HID)

1) Connect the USB cable between scanner and PC.

2) Windows will automatically detect the USB device.

USB (Virtual-COM)

Install driver, USB Virtual COM Driver, from CD-ROM,

The driver will use the next available COM port
number

Connect the USB cable between scanner and PC.

Windows will automatically detect the USB device.

Note:

If any of the above operation is incorrect, turn off the

power immediately and check any improper

connections. Go through all above steps again

Summary of Contents for ArgoxScan 9500



























































































































































Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands

Argox ArgoxScan 9500, Manual

Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands