manualshive.com logo in svg

Argox ArgoxScan 9500, Manual

Share
Download
Argox ArgoxScan 9500 Manual Download Page 123

121

 

OCR Fonts 

 

Default All OCR Settings 

turns off all OCR capability in the 

imager, so the imager will be able to scan linear, stacked, matrix, 

and composite bar codes, but not OCR fonts. In addition, any OCR 

templates you have created are erased. 

The eight digit default templates are reinstated for any future use 

of the 

OCR On 

codes listed below.

 

 

OCR 

Note: 

OCR symbols can misread when scanned sideways or 

upside down. Use 

Working Orientation

, if your OCR symbols will 

not usually be presented upright to the scanner. Only one OCR 

symbology can be read at a time.

OCR-A On 

allows you to scan 

characters in the OCR-A font. The default setting allows you to 

scan any eight digit combination. If you have created an OCR 

template, character combinations that fit the template can be 

scanned. 

OCR-B On 

allows you to scan characters in the OCR-B 

font. The default setting allows you to scan any eight digit 

combination. If you have created an OCR template, character 

combinations that fit the template can be scanned. 

 

 

<Default All OCR Settings>

 

 

 

OCR-A On

 

 

 

 
 

 

OCR-B On

 

 

 

Summary of Contents for ArgoxScan 9500



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands