manualshive.com logo in svg

Argox ArgoxScan 9500, Manual

Share
Download
Argox ArgoxScan 9500 Manual Download Page 114

112

 

B - Beeper: 

Causes a beep to sound after an image is snapped. 

0B No beep (default) 

1B Sounds a beep when the image is captured, notifying the user 

that the imager can be moved. 

E - Exposure: 

This allows you to set the exposure time. Units are 

127microseconds. For example, an exposure setting of 50 

x .000127ms = 6.35ms esposure time. Exposure is used in Manual 

Style only. (Default = 7874)     

nE Range: 0 - 7874 

G - Gain: 

This modifier boosts the signal and multiplies the pixel 

value. The range is 1-8. 

1G No gain (default) 

2G Medium gain 

4G Heavy gain 

8G Maximum gain 

D - Delta for Acceptance: 

This sets the allowable range for the 

white value setting (see W - Target White Value). Delta is only 

available when using Photo Style. (Default = 25) 

nD Range: 0 - 255 

L - LED State: 

Determines if the LEDs should be on or off, and 

when.Ambient illumination (0L) is preferred for taking pictures of 

color documents,such as ID cards, especially when the imager is in 

a stand. LED illumination 

(1L) is preferred when the imager is handheld. LED State is not 

available when using Decoding Style. 

0L LEDs off (default) 

1L LEDs on 

T - Wait for Trigger: 

Waits for a hardware trigger pull before 

taking the image. 

0T Takes image immediately (default) 

1T Waits for a trigger pull, then takes the image 

U - Update Tries: 

The maximum number of frames the imager 

should take to reach the Delta for Acceptance. Update Tries is only 

available when using 

Photo Style. (Default = 6) 

nU Range: 0 - 10 

Summary of Contents for ArgoxScan 9500



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands