Argox ArgoxScan 9500 Manual Download Page 116

Page: 116 / 154

114

C - Compensation:

Flattens the image to account for variations in

illumination across the image.

0C Compensation disabled (default)

1C Compensation enabled

D - Pixel Depth:

Indicates the number of bits per pixel in the

transmitted image (KIM or BMP format only).

8D 8 bits per pixel, grayscale image (default)

1D 1 bit per pixel, black and white image

E - Edge Sharpen:

Causes the transmitted image to be convolved

with an edge sharpening filter. Entering a 23E gives the sharpest

edges, but also increases noise in the image.

0E Don’t sharpen image (default)

14E Apply edge sharpen for typical image

ne Apply edge sharpen using strength n (n = 1-24)

F - File Format:

Indicates the desired format for the image.

0F KIM format

1F TIFF binary

2F TIFF binary group 4, compressed

3F TIFF grayscale

4F Uncompressed binary (upper left to lower right, 1 pixel/bit, 0

padded end of line)

5F Uncompressed grayscale (upper left to lower right, bitmap

format)

6F JPEG image (default)

8F BMP format (lower right to upper left, uncompressed)

H - Histogram Stretch:

Increases the contrast of the transmitted

image. Not available with some image formats.

0H No stretch (default)

1H Histogram stretch

I - Invert Image:

Used to rotate the image around the X or Y axis

in fixed mount applications where the imager is mounted upside

down.

1IX Invert around the X axis (flips picture upside down)

1IY Invert around the Y axis (flips picture left to right)

IF - Fly Spec (Noise Reduction):

Used to reduce salt and pepper

Summary of Contents for ArgoxScan 9500



























































































































































Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands

Argox ArgoxScan 9500, Manual

Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands