Argox ArgoxScan 9500 Manual Download Page 58

Page: 58 / 154

Code 39

Code Page

Code pages define the mapping of character codes to

characters. If the data received does not display with the proper

characters, it may be because the barcode being scanned was

created using a code page that is different from the one the host

program is expecting. If this is the case, scan the bar code below,

select the code page with which the bar codes were created and

scan the value and the

Save

bar code. The data characters should

then appear properly.

Full ASCII On

Code 39 Code Page

*Full ASCII Off

Code 32

Code 32 Pharmaceutical is a form of the Code 39 symbology

used by Italian pharmacies. This symbology is also known as

PARAF.

Note:

Trioptic Code must be turned off while scanning Code 32

Pharmaceutical codes.

Code 32

*Off

Summary of Contents for ArgoxScan 9500



























































































































































Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands

Argox ArgoxScan 9500, Manual

Search results

Summary of Contents for ArgoxScan 9500

Reviews:

Related manuals for ArgoxScan 9500

Brands by name

Popular brands