APRILIA 854239 Service Station Manual Download Page 40

Page: 40 / 216

Exhaust system

Replace silencer acoustic insulation material

CAUTION

BEFORE CARRYING OUT THE OPERATIONS DESCRIBED BELOW, WEAR A PAIR OF SAFETY
GLOVES

•

Remove the connection rivets between

the silencer upper and lower half-shells

operating as follows:

With a commercially available Ø 3mm pin and a

rubber mallet "perforate" the rivets

•

Using a drill with a Ø 5mm point perfo-

rate the rivets completely

•

If necessary, use a commercially avail-

able Ø 5mm pin and a rubber mallet to

remove any remaining shank of the riv-

ets, making sure that both half-shell

holes are free.

CAUTION

MAKE SURE THAT NO RIVET SHANKS ARE LEFT INSIDE
THE HALF-SHELLS

Maintenance

MXV 450

MAIN - 40

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands