APRILIA 854239 Service Station Manual Download Page 188

Page: 188 / 216

•

Position the rear wheel.

•

Position the chain.

•

Working on both sides, insert the cen-

tring shim washers.

•

Working from the left side, insert the

wheel axle.

•

Working on the right side, position the washer and screw but do not tighten the wheel axle

fixing nut.

•

Adjust the chain tension operating the set screws.

•

Tighten the wheel bolt fixing nut.

Locking torques (N*m)

Wheel axle nut - M25

120 Nm (88.51 lbf ft)

See also

Adjusting

Shock absorbers

Adjusting

The rear suspension consists of a spring-shock absorber unit linked to the frame via uniball joints and

to the rear swingarm via a linkage system. To adjust the setting, the shock absorber is fitted with a set

screw that adjusts hydraulic rebound damping (1), with a set screw (2) that adjusts hydraulic compres-

sion damping (low speed), with a knob (6) that adjusts hydraulic compression damping (high speed)

and a ring nut that adjusts spring preloading (3) and a locking ring nut (4).

Suspensions

MXV 450

SUSP - 188

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands