APRILIA 854239 Service Station Manual Download Page 76

Page: 76 / 216

•

Working from the right side, unscrew

and remove the upper nut.

•

From the opposite side, slide off the

screw.

•

Collect the spacers.

•

Lower the engine.

•

After removing the engine, operate on the engine block and place it on the corresponding

engine support plate.

Specific tooling

9100841

Engine support

Installing the engine to the vehicle

•

Place the engine block.

•

Move the engine with small alternating

movements until it is perfectly aligned

with the fixing holes.

•

Fit the swingarm pin.

•

Insert the upper screw, fit the washers

and tighten the nut.

Engine from vehicle

MXV 450

ENG VE - 76

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands