APRILIA 854239 Service Station Manual Download Page 102

Page: 102 / 216

•

Place the control rod together with the

thrust bearing and the shim washer.

•

Place the thrust plate.

•

Fit the clutch springs.

•

Fit the screw washers.

•

Tighten the six screws operating in

stages and diagonally.

Installing the clutch cover

In case of replacement, fit the bearing flush with the machined surface and fit the bushing with the two

oil seals (water and oil) of the water pump using the specific punches.

The drainage hole is turned either -7.5°or +7.5° with respect to an imaginary line drawn between the

bushing centre and the centre of the lower hole used for fixing the water pump cover. See figure.

Engine

MXV 450

ENG - 102

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands