APRILIA 854239 Service Station Manual Download Page 110

Page: 110 / 216

•

Use a micrometer to measure the valve

stem (C) diameter.

•

Use an internal micrometer to measure

the valve guide (D) inside diameter.

Characteristic

Valve stem diameter - minimum limit

4.96 mm (0.1952 in)

Check the clearance (G) between stem and valve guide as follows:

G = D - C

Characteristic

Stem - valve guide clearance - maximum limit

0.08 mm (0.0031 in)

•

If the clearance is not within the speci-

fied values, replace the valve guide.

•

Proceed to check the valves and valve

guides by removing the carbon depos-

its from the valve face and seat.

•

Check that the valve face does not

show cracks and signs of wear; other-

wise, replace the valve.

•

Check that the end of the valve stem is

not distorted (mushroom-shaped) and

that its diameter does not exceed the

stem body diameter; otherwise, re-

place the valve.

•

Check that the value (E) of the valve

support plane of the valve rims is within

Engine

MXV 450

ENG - 110

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands