APRILIA 854239 Service Station Manual Download Page 67

Page: 67 / 216

•

Rear coil - (yellow/black cable):

ground / coil control

Parameters:

coil ignition advance

AXONE: ELECTRICAL ERRORS

Front coil 1351

- malfunction

Error cause:

•

malfunction

Troubleshooting:

•

Check coil primary resistance; if NOT

OK, replace the coil; if OK, check con-

nectors, injector side, control unit side

and voltage regulator /battery side; if

NOT OK, restore the connectors; if OK,

check that there is continuity of the

ground cable between control unit con-

nector and coil connector; if NOT OK,

restore cable harness; if OK, check

that there is continuity of the supply ca-

ble between voltage regulator /battery

connector and coil connector. If OK,

check ground insulation of the positive

cable or ground insulation (with battery

connected but engine off) or that the

negative cable is shorted to positive. If

NOT OK, restore cable harness; if OK,

replace the control unit.

Rear coil 1352

- malfunction

Error cause:

•

malfunction

Troubleshooting:

•

Check coil primary resistance; if NOT

OK, replace the coil; if OK, check con-

nectors, injector side, control unit side

and voltage regulator /battery side; if

NOT OK, restore the connectors; if OK,

check that there is continuity of the

ground cable between control unit con-

MXV 450

Electrical system

ELE SYS - 67

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands