APRILIA 854239 Service Station Manual Download Page 101

Page: 101 / 216

•

Place the washer/s with the tab/s.

CAUTION

RESTORE THE ORIGINAL NUMBER OF WASHERS AND
OBSERVE THEIR ORIGINAL POSITIONS.

•

Place the clutch hub nut.

•

Using the clutch locking tool, tighten the clutch hub nut to the prescribed tightening torque.

•

Fold the locking washer.

Specific tooling

9100896

Clutch housing locking tool

•

Use gearbox oil to lubricate the driving

discs and the driven discs.

•

Place the first friction disc, then the first

1.5 mm (0.059 in) steel disc. After that,

place a friction disc with the reference

tabs in the same slot as for the first disc

and then place a 2 mm (0.079 in) steel

disc until the penultimate disc that will

be the remaining 1.5 mm (0.059 in)

metal disc. Lastly, place the friction

disc with the reference tab one slot

away with respect to the previous

discs.

MXV 450

Engine

ENG - 101

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands