APRILIA 854239 Service Station Manual Download Page 107 | Manualshive

Page: 107 / 216

background image

•

Remove the rocking lever.

Removing the valves

NOTE

THE FOLLOWING PROCEDURE REFERS TO ONE CYLINDER BUT IS VALID FOR BOTH.

•

Remove the control rocker of the exhaust valves and remove the camshaft.

NOTE

BEFORE REMOVING THE CYLINDER HEAD COMPONENTS (VALVES, VALVE SPRINGS, CAPS
AND BUCKET TAPPETS), MAKE SURE THAT THE VALVES ARE PROPERLY CLOSED AND
SEALED.

CAUTION

WHEN REMOVING THE COMPONENTS, MARK THE POSITION OF EACH PART VERY CARE-
FULLY IN ORDER TO PLACE THEM IN THEIR ORIGINAL POSITION UPON FITTING.

•

Remove both pads (1) on both exhaust

valves.

•

Remove both bucket tappets (2) and

both pads under them on the intake

valves.

•

Use the valve springs compressor and

the valve springs compressor adaptor

to remove the valve cotters.

Specific tooling

AP9100838

Tool for valve pressure plate

AP8140179

Valve spring compressor

MXV 450

Engine

ENG - 107

«
...
105
106
107
108
109
...
»

Summary of Contents for 854239

























































































































































































































Reviews:

No comments

Related manuals for 854239

Brand: Honda Pages: 178

Brand: GAS GAS Pages: 32

Brand: VEB Pages: 63

Brand: KTM Power Parts Pages: 12

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 80

Brand: hepco & becker Pages: 3

Brand: Arai Helmet Pages: 20

Brand: Memphis Shades Pages: 2

Brand: Memphis Shades Pages: 2

Brand: Memphis Shades Pages: 2

Brand: HAUL MASTER Pages: 8

Brand: Derbi Pages: 179

Brand: GÜDE Pages: 80

Brand: GÜDE Pages: 88

Brand: Wunderlich Pages: 1

Brand: Wunderlich Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands