APRILIA 854239 Service Station Manual Download Page 214

Page: 214 / 216

- Front and rear suspension efficiency

- Abnormal noise level

Static test

Static check after test drive:

- Restarting when warmed up

- Starter operation (if present)

- Minimum holding (turning the handlebar)

- Uniform turning of the steering

- Possible leaks

- Radiator electric fan operation (if present)

Functional inspection

- Hydraulic braking system

- Stroke of brake and clutch levers (if present)

- Clutch - Check for correct operation

- Engine - Check for correct general operation and absence of abnormal noise

- Other

- Documentation check:

- Chassis and engine numbers check

- Supplied tools check

- Tyre pressure check

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES AS TYRES MAY BURST.

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

Pre-delivery

MXV 450

PRE DE - 214

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands