APRILIA 854239 Service Station Manual Download Page 180

Page: 180 / 216

- retainer ring (2);

- oil seal (6);

- shim washer (5);

- guide ring (4);

- bushing (3);

CAUTION

TO FIT THE OIL SEAL, TAPE THE BUSHING (3) HOUSING SLOT SO THAT THE OIL SEAL LIP IS
NOT DAMAGED.

•

Place shoes made of soft material (alu-

minium) before positioning the stem in

a vice.

•

Place the bushing (3) in its seat on the

stem.

•

Insert the sleeve on the stem.

•

Push the guide ring (4) and the shim

washer (5) on the sleeve until they

stop.

•

Use the proper inserting tool (A) to

push the oil seal (6) in the sleeve until

it stops.

•

Fit the retainer ring (2).

Suspensions

MXV 450

SUSP - 180

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands