APRILIA 854239 Service Station Manual Download Page 151

Page: 151 / 216

•

Turn and remove the start-up system.

•

Disassemble the gear by removing the

Seeger ring (8), the shim washer (7),

the toothed wheel (6), the ball bearing

cage (5), and the shim washer (4).

•

Working from the left side of the gear,

slide off the spring (1) and the start-up

sprocket (2).

•

Carry out the checks described on all

the components mentioned and also

on the shaft (3).

Start-up pedal overhaul

Check gear for cracks and wear and replace it if

necessary.

Check gears movement and, if it is not regular, re-

place the faulty part.

Check the spring and replace it if it is deformed by

over-stretching.

MXV 450

Engine

ENG - 151

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands