APRILIA 854239 Service Station Manual Download Page 171

Page: 171 / 216

Removing the fork legs

•

Undo and remove the two screws fixing

the front mudguard tie rod.

•

Undo and remove the four mudguard

fixing screws.

•

Remove the front mudguard.

•

Place the OPTIONAL front stand in the

hole of the fork lower plate.

•

Undo and remove both calliper fixing

screws.

•

Slide off the calliper.

CAUTION

THE SPEED SENSOR CABLE RUNS OUTSIDE THE CAL-
LIPER AND IS FITTED WITH PROTECTION.

•

Working on the left side, unscrew and

remove the front wheel axle fixing nut.

•

Working on both sides, loosen the screws on the wheel axle clamps.

MXV 450

Suspensions

SUSP - 171

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands