background image

CONDENSATION BOILER 

AQUAKOND AKY

7

code HC0048.01GB ed.B-1406

AKY

1. 

GENERAL WARNINGS

This manual is an essential component of the product and must 

always accompany it. 

If this equipment is sold or transferred to another owner, make 

sure the manual follows it, to enable the new installer/owner 

to consult it.

The manufacturer disclaims any liability (under contract provi-

sions or otherwise) for damage to persons, animals, or objects 

resulting from wrong installation or misuse, and/or non compli-

ance with the manufacturer’s instructions.

This unit is intended only and exclusively for the use for which 

it has been built. Any different, wrong, or unreasonable use is 

to be considered improper and therefore dangerous.

For the installation, the operation and the maintenance of the 

unit, the user shall strictly follow the instructions stated in this 

manual.

Any installation, maintenance or servicing operations shall be 

performed only by authorized personnel, with 

specific techni-

cal skills

 in the heating field.

Any maintenance operations shall be carried out in compliance 

with national laws of the Country where the appliance is installed.

The unit is covered by a guarantee whose conditions and validity 

are specified on the relevant certificate.

The manufacturer declares that the unit is workmanlike built in 

compliance with UNI, UNI-CIG, and EC technical provisions, 

and according to the relevant laws and to the Directive on Ap-

pliances burning gaseous fuels 2009/142/EEC.

2. 

SAFETY WARNINGS

The following symbol is used in this Manual whenever it is 

necessary to draw the operator’s attention on a safety issue.

 

Safety rules for users or operators

 

 

of the equipment and for nearby workers.

This section contains safety rules to be followed for installation 

room and ventilation opening.

2.1.  Fuel

Before starting the unit, check that:

•  Gas supply specifications match those written on the rating 

plate;

•  Combustion  air  inlet  pipes  and  flue  discharge  pipes  are 

exclusively those specified by the manufacturer

• 

The gas seal of the feeding system has been tested and 

approved in compliance with the law.

•  The boiler's fuel is the one specified for the unit

•  The unit is correctly sized to match required flow and includes 

all safety and control devices required by the law;

• 

Gas pipes have been properly cleaned;

•  Fuel rate of flow matches boiler's rated input;

• 

Gas feeding pressure matches values on rating plate.

2.2.  Gas Leaks

If you smell gas:

• 

Do not operate electric switches, the telephone or any other 

object or device that can cause sparks.

• 

Immediately open doors and windows to vent the room.

• 

Close gas valves.

• 

Call for 

qualified personnel.

Summary of Contents for AQUAKOND AKY













































Reviews: