ApenGroup AQUAKOND AKY Installation And Maintenance Manual Download Page 34

Page: 34 / 44

CONDENSATION BOILER

AQUAKOND AKY

code HC0048.01GB ed.B-1406

AKY

C26

R22

C50

C32

U15

C41

C28

R24

R50

R27

R29

CN04

C42

TP1

R83

R101

C54

C55

C18

R91

C35

D16

C12

R90

C34

CN13

D17

C37

R99

C31

SW1

R94

R34

C56

R89

R77

R43

R49

C40

RL2

CN01

LC1

RL1

C51

C11

R70

R41

R40

R35

R59

R96

R38

CN02

D10

C29

C15

C33

D13

R78

R108

R102

R76

R79

C38

R95

C36

C53

R82

XT1

C30

C39

R63

R54

C46

RR1

C16

CN06

LC3

R30

R36

R86

D19

CN07

R84

D15

R93

RD1

C47

LC4

R92

R51

R85

R75

CN03

R33

NTC3
NTC3

NTC2
NTC2
NTC1
NTC1

D-

D+

GND

+12V

GND
7Vdc

24Vac
24Vdc

CLK
DAT

HC0047 C2 012

1 2

3 4 5 6

Switch for chronother-

mostat

6.7. Replacing Modulation Board

When replacing the board, some checks have to be carried out

and some parameters have to be set using the LCD display or

SmartControl.

AKY boilers use a default list of values. Please update this list

each time a change is made so that replacement boards can

be precisely configured, if necessary.

* The following information refer only to AKY boilers. For other

equipment using the same modulation board, please refer to

relevant manual.

Verifying hardware configuration of the board

Change the board address using the switches and take note of

the configuration of the board just replaced.

Setting up parameters

Parameters that must necessarily be set are the following:

•

d0, d1, and d5: they identify the type of appliance

•

b1, b2, and b3: they regulate the number of revolutions of

the motor of flue fan

•

S1 enables NTC1 sensor on hot water delivery

• S3 enables flue control

•

S5 enables B2 sensor to control water pressure

• S6 enables B3 sensor to control water flow rate

•

H11 enables Y1 (PWM2) outlet for water circulator modula-

tion (only for standard model).

Parameter setting - Operative mode

Parameters can be modified using LCD display on the boiler

or SmartControl.

SmartControl allows access to all parameters (see tables in next

pages). Parameters are password protected. The password is

supplied by Apen Group Service.

See SmartControl manual for accessing and changing operation

parameter. Parameters can only be changed with burner OFF.

6.8. Configuring with LCD Display

Parameters are shown and can be changed only if they have

been enabled using

Abi

menu password.

To change parameters, the board address must be 0. If it is not,

change the address to 0.

Abi (set point change enabled)

Passwords for

Abi

menu are the following:

(-)

Enables the change of boiler set points, listed under

Set

menu. Password is 1 (one)

(-)

Enables the change of boiler parameters, listed under

Par

menu. This password is used by service staff and must be

requested to APEN GROUP SPA

If no keys are pressed for 10 minutes after entering the pass-

word, previous state is automatically restored.

Use arrows to scroll the menu. Press ENTER to select a pa-

rameter or set point, then use arrows to display required value.

Press ENTER for 3 seconds to confirm. The value will flash on

display to confirm it has been stored.

Set Point Menu

Meaning and default values of each parameter are listed in

parameter table.
H51

Not used

H52

Not used

H53

Not used

St1

Modulation temperature

St2

Not used

H43

Flue control - See parameter table

H44

Flue control - See parameter table

H45

Flue control - See parameter table

St5

Pressure in hydraulic system

St6

Flow rate in hydraulic system

Summary of Contents for AQUAKOND AKY













































Search results

Summary of Contents for AQUAKOND AKY

Reviews:

Related manuals for AQUAKOND AKY

Brands by name

Popular brands

ApenGroup AQUAKOND AKY, Installation And Maintenance Manual

Search results

Summary of Contents for AQUAKOND AKY

Reviews:

Related manuals for AQUAKOND AKY

Brands by name

Popular brands