ApenGroup AQUAKOND AKY Installation And Maintenance Manual Download Page 40

Page: 40 / 44

CONDENSATION BOILER

AQUAKOND AKY

code HC0048.01GB ed.B-1406

AKY

WIRING DIAGRAMS

For connections, see section on Installation.

Wiring diagrams and operating principle are the same for all AKY boilers. Differences are listed below.

AKY070 boilers have an additional safety device installed on max water pressure. If this device triggers, an F21 error

is issued and manual reset is required.

STB

Safety thermostat has manual reset. If it triggers, an F20 lock is issued, that needs to be manually reset from electronic

board using reset button on flame control device.

ON/OFF A room thermostat must be installed on each boiler.

If a SmartControl [G22800IT] is used, create a jumper on ID2/IDC2 terminals. All previously referred accessories work

as room thermostat.

Summary of Contents for AQUAKOND AKY













































Search results

Summary of Contents for AQUAKOND AKY

Reviews:

Related manuals for AQUAKOND AKY

Brands by name

Popular brands

ApenGroup AQUAKOND AKY, Installation And Maintenance Manual

Search results

Summary of Contents for AQUAKOND AKY

Reviews:

Related manuals for AQUAKOND AKY

Brands by name

Popular brands