manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

15

15 – 100

Because of the read-first, write-second characteristic of the processor,
using the same register as destination in one clause and a source in the
other is legal. The register supplies the value present at the beginning of
the cycle and is written with the new value at the end of the cycle.

For example,

(1) DM (I0, M0) = AR, AR = AX0 + AY0;

is a legal version of this multifunction instruction and is not flagged by the
assembler. Reversing the order of clauses, as in

(2) AR = AX0 + AY0, DM (I0, M0) = AR;

results in an assembler warning, but assembles and executes exactly as the
first form of the instruction. Note that reading example (2) from left to
right may suggest that the result of the computation in AR is then written
to memory, all in the same cycle. In fact, this is not possible. The left-to-
right logic of example (1) suggests the operation of the instruction more
closely. Regardless of the apparent logic of reading the instruction from
left to right, the read-first, write-second operation of the processor
determines what actually happens.

Status Generated: 

 All status bits are affected in the same way as for the

single function versions of the selected arithmetic operation.

<ALU> operation

ASTAT:

7

6

5

4

3

2

1

0

SS

MV AQ AS

AC AV AN AZ

-

-

-

*

*

*

*

*

AZ

Set if result equals zero. Cleared otherwise.

AN

Set if result is negative. Cleared otherwise.

AV

Set if an overflow is generated. Cleared otherwise.

AC

Set if a carry is generated. Cleared otherwise.

AS

Affected only when executing the Absolute Value operation
(ABS). Set if the source operand is negative.

MULTIFUNCTION

COMPUTATION with MEMORY WRITE

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Hama HDD Silenser Bedienungsanleitung preview
HDD Silenser
Brand: Hama Pages: 12
TP-Link VIGI NVR1008 Quick Installation Manual preview
VIGI NVR1008
Brand: TP-Link Pages: 2
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Brand: Concept Pro Pages: 28
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
Uctronics U6187 Assembly Manual preview
U6187
Brand: Uctronics Pages: 12
Z3 Technology FSDI-1XA User Manual preview
FSDI-1XA
Brand: Z3 Technology Pages: 83
Behringer X-MADI Quick Start Manual preview
X-MADI
Brand: Behringer Pages: 15
Intel Core 2 Duo E4300 Design Manual preview
Core 2 Duo E4300
Brand: Intel Pages: 55
Avaya VSP 8284XSQ-AC Quick Install Manual preview
VSP 8284XSQ-AC
Brand: Avaya Pages: 2
Paradyne Application Module 9109 OCU-DP Installation Instructions Manual preview
Application Module 9109 OCU-DP
Brand: Paradyne Pages: 8
FiberHome AN5506-04 Series Product Manual preview
AN5506-04 Series
Brand: FiberHome Pages: 146

Brands by name

Popular brands

Load more brands