manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

7 Host Interface Port

7 – 4

The functions of the following pins are determined by HMD0 and HMD1
as described above:

HD15-0/HAD15-0 are either a data bus or a multiplexed address/data
bus. (Only the 3 least significant address bits are used.)

HRD

/HRW is either a read strobe or a read/write select (1=read, 0=write).

HWR

/

HDS

 is either a write strobe or a data strobe.

HA2/ALE is either the most significant host address bit or an address
latch enable.

HA1-0 are either the two least significant host address bits or are unused.

7.3

HIP

FUNCTIONAL DESCRIPTION

The HIP consists of three functional blocks, shown in Figure 7.1: a host
control interface block (HCI), a block of six data registers (HDR5-0) and a
block of two status registers (HSR7-6). The HIP also includes an associated
HMASK register for masking interrupts generated by the HIP. The HCI
provides the control for reading and writing the host registers. The two
status registers provide status information to both the host and the ADSP-
21xx core.

The HIP data registers HDR5-0 are memory-mapped into internal data
memory at locations 0x3FE0 (HDR0) to 0x3FE5 (HDR5). These registers
can be thought of as a block of dual-ported memory. None of the HDRs
are dedicated to either direction; they can be read or written by either the
host or the ADSP-21xx. When the host reads an HDR register, a maskable
HIP read interrupt is generated. When the host writes an HDR, a
maskable HIP write interrupt is generated.

The read/write status of the HDRs is also stored in the HSR registers.
These status registers can be used to poll HDR status. Thus, data transfers
through the HIP can be managed by using either interrupts or a polling
scheme, described later in this chapter.

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Brand: Orban Pages: 255
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
protech ProX-1695 User Manual preview
ProX-1695
Brand: protech Pages: 95
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Brand: DCB Pages: 28
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
EZCast Pro Dongle II D10 Repair Manual preview
Dongle II D10
Brand: EZCast Pro Pages: 4
ekwb EK-FC R9-295X2 Installation And Mounting Manual preview
EK-FC R9-295X2
Brand: ekwb Pages: 2

Brands by name

Popular brands

Load more brands