manualshive.com logo in svg

Analog Devices adsp-2100, Manual

The Analog Devices ADSP-2100 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and valuable insights on utilizing the ADSP-2100 effectively. Unlock the full potential of this exceptional product by accessing the manual from manualshive.com.

Share
Download
background image

Computational Units

2 – 3

2

2.1.6

MAC Arithmetic

The multiplier produces results that are binary strings. The inputs are
“interpreted” according to the information given in the instruction itself
(signed times signed, unsigned times unsigned, a mixture, or a rounding
operation). The 32-bit result from the multiplier is assumed to be signed,
in that it is sign-extended across the full 40-bit width of the MR register
set.

The ADSP-2100 family supports two modes of format adjustment: the
fractional mode for fractional operands, 1.15 format (1 signed bit, 15
fractional bits), and the integer mode for integer operands, 16.0 format.

When the processor multiplies two 1.15 operands, the result is a 2.30
(2 sign bits, 30 fractional bits) number. In the fractional mode, the MAC
automatically shifts the multiplier product (P) left one bit before
transferring the result to the multiplier result register (MR). This shift
causes the multiplier result to be in 1.31 format, which can be rounded to
1.15 format. Figure 2.7, in the MAC section of this chapter, shows this.

In the integer mode, the left shift does not occur. For example, if the
operands are in the 16.0 format, the 32-bit multiplier result would be in
32.0 format. A left shift is not needed; it would change the numerical
representation. Figure 2.8 in the MAC section of this chapter shows this.

2.1.7

Shifter Arithmetic

Many operations in the shifter are explicitly geared to signed (twos-
complement) or unsigned values: logical shifts assume unsigned-
magnitude or binary string values and arithmetic shifts assume twos-
complement.

The exponent logic assumes twos-complement numbers. The exponent
logic supports block floating-point, which is also based on twos-
complement fractions.

Summary of Contents for adsp-2100







































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for adsp-2100

C4i U1000 User Manual preview
U1000
Brand: C4i Pages: 8
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
Jabra A330 Multiuse User Manual preview
A330 Multiuse
Brand: Jabra Pages: 15
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Brand: Raritan Pages: 4
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
Edge-Core SDW100 Quick Start Manual preview
SDW100
Brand: Edge-Core Pages: 7
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
ZyXEL Communications GS3700 Series Handbook preview
GS3700 Series
Brand: ZyXEL Communications Pages: 215
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Brand: Cytron Technologies Pages: 13
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Brand: Lattice Semiconductor Pages: 12
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
National Instruments NI 653x User Manual preview
NI 653x
Brand: National Instruments Pages: 147

Brands by name

Popular brands

Load more brands